Sanus Wall Mount

Magnavox flat-screen LCD TVs offer two separate means of installation. A base that can be attached to the bottom of the flat screen comes in the box with a Magnavox LCD when you buy it, and Magnavox flat screens also provide screw holes on the back that can be used to mount the TVs with a compatible wall mount. Mounting the Magnavox LCD flat-screen television can save space in your home by eliminating the need for a TV stand.

Instructions

1 Get a wall mount that fits the size and weight specifications of your Magnavox LCD TV. Wall-mount kits list on the packaging the maximum dimensions and weight of a television that the mount can safely support.
2 Mark the wall where you want to hang the Magnavox LCD television. Crutchfield states that you should hang an LCD TV so that the middle of the screen is approximately eye level when you sit down to watch television. Therefore, you should measure the distance from the floor to eye level when you sit on the couch or other main seating in the room with a measuring tape and then add a few inches to that measurement to determine where the top of the screen should hit. Next, measure that distance up from the floor and mark several places across the wall where the top of the screen should hit.
3 Find the studs in the wall with a stud finder. Next, find the middle of each stud. Crutchfield recommends finding the stud center by tapping a nail into the wall where the stud is located until the nail hits the stud, removing the nail and moving it over inch and tapping it in again. Do this in both directions across the stud and, when you find nothing but drywall on either side, measure the distance between the holes and mark the middle.
4 Measure between the screw holes on the wall bracket part of the TV mount. Transfer the distances between the screw holes on the mount to the wall, marking the location where each screw should go and trying to keep the screw locations in the center of the wall studs whenever possible. Screw the bracket into the wall using the screws provided with the wall mount.
5 Attach the TV bracket part of the wall mount to the mounting holes on the Magnavox LCD TV. To attach, simply use the screws provided to screw the bracket into the holes. Once both parts of the wall mount have been installed, lift the bracket on the LCD TV up and over the wall bracket and lower the TV until the brackets of the wall mount lock into place.

Mounting a TV to a wall has become standard fare, thanks to lightweight flat-panel LCD and plasma televisions. You can mount a TV to a striped wall, providing you have purchased a TV wall-mounting kit from an electronics store or a home and garden shop. The backs of LCD and plasma televisions employ a standard mounting scheme, so any brand-name wall-mounting kits can be used. A few household tools will be needed as well.

Instructions

1

Measure the width between the two grooves on the back of the TV that the TV brackets from the TV wall-mounting kit will be attached to -- use a tape measure to do this.

2

Place a dot on the wall with a pencil at the height where you want the TV to be. Measure across from the dot on the wall using the tape measure. Make another dot on the wall where the measurement that was taken from the back of the TV is reached.

3

Place a stud finder against one of the dots on the wall and move it left and right until the needle twitches, indicating a stud. Make an "X" at this point with the grease pencil. Repeat this procedure at the other dot on the wall.

4

Place the TV wall bracket against the striped wall, with the holes in the bracket lined up with the dots made on the wall. Partially screw in a metal screw in the two dots on the wall with a power drill screwdriver.

5

Place a spirit level against the top edge of the bracket. Adjust the bracket so that the bubble in the spirit level is evenly between the two lines on the information panel. Screw the two screws all the rest of the way in. Screw in metal screws through the other holes in the bracket.

6

Place a TV frame from the TV mounting kit into each of the two grooves on the back of the TV. Screw metal screws through each TV frame into the back of the TV using a Phillips screwdriver.

7

Lift the TV and insert the TV frames into the grooves in the TV wall bracket. Tighten the set screws to secure the TV frames in the bracket.

To take advantage of a flat panel TV's slim design, wall mounting is the choice for a high-tech, space-saving decor. There are plenty of options for purchasing a wall mount, but another option is to build one yourself.

Instructions

1

Trim the horizontal bracket to a length slightly smaller than the width of your TV.

2

Cut the vertical bracket into two pieces, each measuring about 12 inches.

3

Cut a notch into each end that is identical to the factory-cut notches at the other end. You now have two vertical brackets with two notches in each of them.

4

Line up the vertical brackets with the screw mount holes on the back of the TV, and mark where you need to drill for the screws to fit.

5

Place weather-strip on the side that will mount to the TV.

6

Place weather-strip on the thicker side of the horizontal bracket that will be attached to the wall.

7

Find the stud in the wall and screw one screw into the stud. Find the second stud and mark where you need to drill for the second stud screw. Drill the hole for the second screw.

8

Place the horizontal bracket against the wall, and mount with large grabber screws.

9

Now the horizontal bracket is attached to the wall. Next, attach the vertical brackets to the TV.

10

Screw the vertical brackets onto the back of the TV and slide them under the lip of the horizontal bracket until it fits in the slot. Hang the TV.

LG flat panel televisions, to many owners and interior designers, look their best when wall-mounted. LG sets support the VESA or Video Electronics Standards Organization mounting protocol. This means that for the installer, selecting virtually any compatible mount is the correct option, depending on the installation requirements. LG TVs offer a variety of size options, all capable of wall mounting. Regardless of the size or installation, LG sets offer slim aesthetics, ideal for wall mounting.

Instructions

1

Move the stud finder along the intended mounting wall. Locate two studs and mark their locations with the tip of the drill bit.

2

Place the wall bracket half of the wall mount against the wall, in concordance with the marked studs. Drill through at least four of the bolt holes with the 3/16-inch bit.

3

Insert the included lag screws and washers through the wall bracket and into the drilled holes. Tighten them fully using the socket wrench and inserts.

4

Locate the inserts on the rear of the LG set. These are gold-colored threaded metal inserts, designed to accept the included Allen bolts. Align the TV bracket with these inserts.

5

Insert the included Allen bolts through the holes in the bracket, tightening them securely with the included Allen key.

6

Lift the LG set onto the wall bracket, using an assistant if necessary. Align the TV using the level. Tighten any securing set screws using the Allen key, included with the mount.

Flat screen LCD televisions have amazing space-saving capabilities and use less energy than older CRT televisions. Typically, LCD televisions come equipped with a stand that will allow you to position it on a flat surface such as a home entertainment cabinet. Mounting LCD televisions on a wall requires you to purchase and install a special wall mount for a safe and sturdy fit. Larger LCD televisions should be mounted with the aid of an additional person.

Instructions

1

Take both the LCD television and the wall mount accessories out of their boxes. If your television came with the regular stand mounted on the bottom, remove the stand according to your television's documentation with an appropriate sized screwdriver.

2

Determine the mounting location for the television and decide how you are going to run the audio, video and power cords to your television. Have a qualified electrician install a new electrical outlet as well as any other home theater wiring inside the wall for a cleaner look. Alternatively, you can purchase and install a wiring loom on the outside of your wall to hide your televisions wiring (these wiring hiding looms are typically flat and can be painted to match your wall).

3

Install the two metal brackets that came with your wall mount kit on the back of the TV. These brackets are long, channeled and feature multiple holes for you to choose from so you can mount them to different brands and TV sizes. Your mounting kit will come with different sized bolts or screws; you must find the appropriate size that will screw into the holes used for a TV mount on the back of the LCD television.

4

Double-check the tightness of the mounting brackets installed on the back of your TV. Make sure the brackets are evenly spaced from the top and bottom portions of the television. Install the two hooked bracket hangers on the mounting plate temporarily (the mounting plate resembles a large piece of sheet metal with a flange on both the top and bottom). Install the hooked bracket hangers with the mounting plate attached on the mounting brackets installed on the television and measure the distance from the top of the wall plate to the top of the television.

5

Measure the distance from the side edge of the wall plate to the side edge of the television and write down these figures. These measurements will allow you to determine the correct mounting area for the television before you install the wall plate to the wall. The hooked bracket hangers are designed to slide from left to right on the flanged portion of the wall plate; make sure the wall plate is centered from right to left when you temporarily install it on the back of the television for accurate measurements.

6

Unhook the wall plate from the rear of the television and find your wall studs with a stud finder in the area where you wish to mount the television (the studs run vertically inside your wall). Mark the center of the studs with a pencil, using the wall plate as a template when marking the stud locations. There are multiple hole slots available on the upper and bottom portion of the wall plate that you can use.

7

Rest a level on top of the wall plate before using a drill to screw in the four bolts needed to secure the wall plate to the wall (two bolts top and bottom, on both right and left sides of the wall plate. The level will help you evenly mount the television to the wall). If your drill is not powerful enough to drive the bolts into the studs, drill pilot holes with a small drill bit and tighten the bolts using a ratchet tool.

8

Check the levelness of the wall plate again after you tighten down the bolts. Ask another person to help you lift the television and place it on the wall plate. The hooked brackets mounted on the television must slide over the upper flange of the wall plate so it can support the television. Certain mounts may have a flat rod that needs to be inserted in the bottom flange to secure the bottom potion of the television to the wall plate.

9

Hook up your audio, video and power cables to the television. If you are installing a wiring loom to hide your television cables, go ahead and install this now according to the product's instructions. Place the level on top of your television once more to check for levelness.

Some homeowners like to create an attractive focal point in their den or living room by mounting a flat-screen TV on a brick wall. The job requires different hardware with more specialized drill bits. But with the proper tools and planning, the results can be impressive.

Instructions

1

Place the bracket on the wall. Align at least 4 bolt holes on the brick (not the mortar) at the desired mounting height. Mark these locations with a pencil or the drill bit tip.

2

Drill the marked locations with the masonry bit. Make sure the bit penetrates at least 1/2-inch deeper than the maximum depth of the expanding anchors.

3

Insert the expanding sleeves into the drilled holes. Tap them in flush with the brick, using the hammer.

4

Place the wall bracket over the sleeves so the bolt holes are aligned with the sleeve openings. Insert the bolts and washers through the mount's holes and hand-tighten. Secure the rest of the way with the socket wrench and appropriate insert.

5

Give a quick tug on the bracket to ensure it is mounted securely.

Most flat screen TVs are VESA-compatible and designed to mount on a wall. "VESA" refers to standardized mounting holes on the back of plasma or LCD TVs. Although installation is fairly simple, getting power to the set can be a challenge. The easiest and neatest way to accomplish this is to have a licensed electrician install an outlet behind your proposed TV. Once an outlet is installed, thread your coaxial and speaker cables up to the TV between two studs behind the drywall.

Instructions

1

Slide an electronic stud finder across the wall to locate two suitable wall studs; the instrument will beep when it reaches the edge of a stud. Lightly mark the position of the middle of the studs on the wall with a pencil. Run the stud finder up the wall between the studs to ensure that there is no hidden fire block or obstruction preventing threading the coaxial cable up to the TV.

2

Lift the TV mounting bracket up to the desired height and location. Move the bracket until the two mounting holes line up with the center of the hidden studs. Place a spirit level horizontally on the bracket and center the bubble. Insert the tip of a pencil into each mounting hole and mark its outline with a circle.

3

Drill two lag bolt holes into the studs through the two circles with the recommended pilot drill bit and a cordless drill/driver. Position the bracket against the wall and insert the lag bolts that came with the kit into both pilot holes. Snug the bolts down with a socket wrench.

4

Level the bracket with the spirit level by tapping one side up or down until the bubble is centered. Tighten the lag bolts securely.

5

Drill a 1/2-inch hole through the drywall in the middle of the large opening on the mounting bracket. Drill a second 1/2-inch hole above the skirting board directly below the first hole. Insert a fish tape through the upper hole, thread it downward and fish the end out from the lower hole with a bent piece of thin wire.

6

Tape the end of the coaxial and speaker cables securely to the fish tape. Pull the fish tape up while feeding the cables through the hole from the bottom, and fish the ends out through the upper hole.

7

Lay your Polaroid Plasma TV face down on the carpet or on a thick towel. Pry the four plastic plugs out of the VESA mounting holes on the back of the TV with a thin screwdriver. Place the swivel or wall mount that came in the kit on the TV and line up the mounting holes. Attach the mount to the TV securely with the screws provided in the kit; use a Phillips screwdriver or nut driver, whichever is applicable.

8

Lift the TV into place with the help of a friend. Attach the security cable provided to the back of the swivel mount by following the instructions in the manual. Connect the coaxial and speaker cables to the TV.

9

Hook the upper lip on the swivel or TV mount bracket over the matching recess on top of the wall mounting bracket, and lower the TV into place.

10

Plug the power cord into the previously installed outlet behind the TV to complete the installation

Deciding where to mount your TV in your bedroom can be a difficult decision to make. If you follow the advice below, however, you will be on your way to finding the ideal place to mount your television.

Eye Level

For optimized viewing, the center of the television screen should be at the eye level of where you watch TV most. Although this may be the best angle to view the screen, it may not be aesthetically well located on the bedroom wall. This also means that the TV will be mounted rather low and may get in the way of your furniture.

Treat It Like Artwork

One common idea is to treat your television like a piece of art. Imagine where you would hang a poster or a painting. This is generally much higher on the wall compared to the method mentioned above. However, you can compensate for the height difference by purchasing a tilting mount, which allows you to angle the TV downward.

Other Considerations

If you have already purchased cables, remember to mount the TV within the proper distance of your components so the cables can reach. Also remember that the power cable needs to be able to reach an outlet.

Mounting a TV on the wall requires more than just tools and a TV mount. It also requires thought and consideration. If you hang the TV in the wrong spot, you will either have to move it, causing unsightly holes in your wall; or you will have to watch television in a way that is uncomfortable. Fortunately, the procedure to determine where to mount the TV is simple.

Finding a Place

The hardest part about finding a place for a television mount is finding a place to hang it. TV mounts must be hung from the wall studs. If you do not hang the mount from the wall stud, your television will come crashing down from the wall and break into pieces and be completely ruined. The easiest way to find the studs in your house is to use a stud finder. This piece of equipment will locate the studs when pressed against the wall. You will want to mark the location of two to three studs in the area where you want to hang the TV. Make sure the studs go all the way to the floor for stability.

Consider Furniture

Inspect the furniture that you have. Do you have a TV stand that you want to place under the television? The TV will have to be hung high enough so that it does not touch the top of the table or get covered by the table. Use a measuring tape to determine the height of the table. Make a mark on the wall with a pencil to show where the top of the table will hit. Now look at what you are going to be sitting in as you watch television. Will you sit on a sofa? Chair? Or you do intend to sit on a low chair such as a gaming rocker? This will also help determine where to place the TV on the wall. Sit in the seat and stare straight ahead. You can hold a laser pen at the same level as your eyes and flash it on the wall. Mark this height with a pencil. The middle of the television will ideally be located near that mark.

Trying Heights

Measure your television. Make a large square out of paper that matches the measurements of your television. Tape the piece of paper onto the wall where you want to hang the TV. Try several different heights between the lowest height (right above the measurement for the table) and the highest height (resting on the bottom of the eye-line mark). Find a comfortable place where your head does not feel strained or uncomfortable when looking at the paper. Mark this level with a pencil and mount the television to the wall at that place.

Incorrectly installing a flat-screen TV on your wall leads to a broken television, a damaged wall and possible injury to yourself, others or even pets if the TV happens to fall. Knowing how to properly install your flat-screen TV on your wall saves you money that would otherwise be spent on a professional installation of your TV, repairs to your damaged property or even medical bills in the case of injury.

Instructions

1

Locate two vertical studs, or beams, in the wall. Slide the stud finder along the wall in the area where you are installing your flat-screen TV. The stud finder beeps when it finds a beam in the wall. Use the pencil to mark the location of the studs in the wall. The standard stud separation distance is 16 inches, so the two beams will be 16 inches apart from each other.

2

Position the wall plate so it lies over both of the studs. Insert the lag bolts that came with your wall mount into the mounting holes of the wall plate, then tighten them with a wrench.The wall mount is now attached to the wall.

3

Remove the base of your flat-screen TV. This increases the visual appeal of the TV on the wall and reduces the weight you are putting on the wall mount. Lay a soft blanket on a flat surface, slowly tilt your TV forward so it is laying face-down on the blanket, remove the small screws in the back of the TV near the TV's base, then gently pull the base from the TV.

4

Add the TV mounting brackets that came with the wall mount to the back of the TV. Position the brackets so the hole openings are aligned over the VESA holes on the back of the TV, then tighten them with a Phillips screwdriver. The VESA holes are designed to connect your TV to the wall mount.

5

Lift the TV onto the wall-mounted plate and align the brackets onto the wall plate. Insert the security screws that came with the wall mount through the brackets and into the wall plate, then tighten them with a Phillips screwdriver. Your flat-screen TV is now installed on your wall.

Stop wasting space with your LCD TV sitting on a stand and mount a bracket on the wall for it to hang. LCD TVs are designed to hang on the wall, allowing you to save space in your room for other things. TV wall mounts come in different sizes. Wall mount boxes should be labeled with the size of TV those mounts support. Follow these easy steps to mount the appropriate brackets to your wall.

Instructions

1

Find studs in your wall. You need to mount the brackets on the studs because attaching them to the drywall will likely lead to the bracket tearing off the wall when the weight of the TV is added. Studs can be found with a stud finder or by knocking on the wall until you hear a solid sound rather than a hollow one.

2

Determine where on the wall you want the wall mount to hang. Proper viewing height should be at the center line of an LCD TV screen, equal to eye height. You don't want to look up or down a lot while viewing the TV because this may cause neck strain.

3

Mark in pencil the spot on the wall where you want the mount to hang. Don't mark in pen because you don't want to leave a permanent mark on the wall and you want to be able to make corrections, if necessary. Double-check to make sure the markings are on a spot on the wall where a stud is located.

4

Drill heavy-gauge screws into the wall where you made your marks. Regular screws probably won't be able to withstand the weight of the mount when the LCD TV eventually gets hung.

5

Test the sturdiness of the mount by grabbing the top and pulling down. If secured properly, the mount won't move or cause the wall to crack.

Almost all wall-mounted TVs are flat screens, which often resemble paintings as much as sophisticated pieces of technology. Like artwork, they look quite good suspended halfway up a wall, and mounting them saves shelf space for other purposes. Wall mounts themselves typically consist of two pieces--one secured to the wall, one screwed into the TV--which lock together to keep the TV secure. If installed properly, there should be no danger of slipping or falling.

Instructions

1

Gauge the wall space where you wish to mount the TV. It needs to be large enough to fit the set itself, positioned so that you can watch it comfortably without craning your neck. Allow for a certain amount of play in your chosen location so that you can place it in the strongest spot on the wall.

2

Use a stud finder to locate the studs in the wall, marking the locations with a pencil. The studs will provide a strong anchor for your TV mount--far stronger than regular plaster or drywall.

3

Hold the back half of the wall mount up against the wall, lining the screw holes up with the studs.

4

Secure the wall mount to the wall with bolts or lag screws, then tighten them with a socket wrench. Double-check the screws to make sure they are as tight as you can make them.

5

Place the TV, screen-side down, on top of a comforter or similar padding. You need comfortable access to the back of the TV without scratching or damaging the screen.

6

Disconnect the stand-up mount at the bottom of your TV if it has one.

7

Find the mounting sockets on the back of the TV, then align them with the front half of the TV mount. Secure the front half of the mount to the TV with a screwdriver.

8

Lift the TV over to the back half of the wall mount and fit it into place. Flat-screen TVs are heavy, so get a friend to help you with this step.

9

Snap the locking mechanism closed on the TV mount and give it a few gentle pulls. There should be no play or wiggle at all.

10

Leave the TV be for 1 to 2 hours, then give it another look. Sometimes wall mounts will sag a bit over time, even if they seem secure when you first install them.

Hanging a TV on a wall mount should only include a few basic steps after the wall mount is fastened to the wall. Youll save a lot of space in any room with a TV that is mounted to the wall. Ensure the wall mount is safely fastened to the wall before hanging your TV. Wall mounts need to be fastened to studs in walls. Walls with no studs wont be able to withstand the weight of the wall mount and TV. Heavy gauge screws will provide the proper strength and support.

Instructions

1

Clear the floor area around the wall mount of any furniture or wires to avoid tripping.

2

Lift the TV into the air and place it on the wall mount. Have someone help you lift the TV if its big or heavy. Refer to your wall mount's owners manual if you're unsure of the proper way to hang the TV. Different wall mounts might require different procedures.

3

Attach all media device cables to the TV, such as cable or satellite boxes and DVD players. Some TV mounts wont allow enough room to plug in cables when the TV is hung from the mount. Cables should be plugged into the TV before its lifted onto the mount if this is the case.

4

Plug all power cords into wall outlets and power the TV on. You should now be able to watch your TV with it hung from the wall.

As strange as it may seem, TVs nowadays are made to be mounted on a wall. New TVs have four holes spread out in a box shape on the back of them called "VESA Holes." Luckily, TV mounting brackets also have VESA holes that allow the bracket to connect to the back of your TV with the use of "VESA Screws." The process for putting together a TV wall-mount bracket uses common household tools and doesn't take long to complete.

Instructions

1

Locate two studs by running a stud finder against the wall until the stud finder indicates the presence of a stud with a loud beeping noise. Mark the location of the stud on the wall with a pencil. The wall mount comes in two main pieces, the wall bracket and the TV bracket.

2

Hold the wall bracket against the wall so the mounting holes line up over the wall studs, and mark the location of the mounting holes on the wall with a pencil.

3

Remove the wall bracket, then drill out the mounting holes in the wall. Place the wall bracket back against the wall and insert a lag bolt that came with your wall mount through each mounting hole of the bracket. Tighten the lag bolts into the wall studs using a wrench.

4

Turn the TV around so the back faces you. Line up the TV bracket to the TV, insert the VESA screws through the bracket and use a Phillips screwdriver to tighten the screws into the TV.

5

Pick up the the TV and align the TV bracket that is connected to the back of the TV to the wall bracket that's installed on the wall. Fit the connections of the TV bracket into the connections of the wall bracket. Tighten the security screws using a Phillips screwdriver.

Technological advancements in the last 10 years provide new applications for televisions like Plasma, light-emitting diode (LED) and liquid crystal displays (LCD) screens in flat-panel formats. The shallow depth of these televisions allow for wall hanging.

Types

Three primary types of wall mounts are available for mounting a Plasma TV. The first is the full motion mount, which allows for rotation of the TV away from the wall at nearly every angle. The second is a tilt mount, which allows for adjusting the vertical angle. The third and final mount is the low profile mount, which is meant for invisibility.

Where to Buy

Any major retailer that sells flat panel televisions like Plasma and LED screens carries the appropriate TV mounts. A few competing shops include Best Buy, Target and Fry's all of which sell mounts online as well as in their retail locations.

Price

Prices vary greatly in wall mounts. Some mounts are found for as little as $14.99 for a standard mount or as much as $999.99 for a motorized wall mount in October of 2010. Purchasing online is easiest, but does not provide the opportunity to see the mount in action.

If you want to hang any flat, mountable TV on the wall you need a wall mounting kit made for your TV. You'll need to know how to manage all the audio/video cables that connect your TV to the stereo system, gaming units and anything else you have hooked up. The easiest way to prevent a mess of wires is to install a decorative cable raceway. Cable raceways come in several styles and colors or can be painted to match your decor.

Instructions

1

Find your studs with a stud finder. They vary by manufacturer, but you run them slowly across the wall and a beep or light change indicates the location of a wall stud. Mount your TV to a stud, even if it's not centered on your wall; studs are solid wood, and drywall alone won't support the weight of a TV.

2

Place the wall bracket over the stud at the height you want to hang the TV. Drill pilot holes and use the screws that came with your kit to secure the bracket to the wall.

3

Check the bracket with a level to make sure it's perfectly horizontal. If if isn't you'll end up with an off-kilter TV. Make any adjustments if needed and use a socket wrench to do the final tightening of the screws.

4

Remove your TV's stand if necessary and attach the TV mounting bracket that came with your kit. Use the provided washers and bolts. Make sure the bracket is securely attached to the TV.

5

Lift the TV and clip the TV bracket into the wall bracket. Use a helper for this part of the process. One person should support the weight while the other guides the clip into place.

6

Run the cables through a cable raceway below the TV. There are usually two channels: one for A/V cables and one for the power cord. Don't place them in the same channel or you'll have interference in your signal.

7

Screw or tack the raceway to the wall according the directions provided with your raceway kit. You can paint it to match your wall paint color if you want.

8

Tie wires together at the bottom end of the raceway and tack them to the baseboard with wire tacks if necessary. Remember not to bundle the power cord with the other cables.

Many people mount their televisions to the wall in order to save space and for aesthetic appeal. But they often forget about the cables that run from their electronic devices to the TV. Hiding the cables for your Blu-ray player, game systems, cable boxes and other electronic devices doesn't require much more work, but it does take advance planning before mounting the TV. Once the TV is mounted, it will conceal the hole needed to hide the wires behind the wall.

Instructions

1

Locate two vertical studs in the wall using a stud finder. Mark the location of the studs on the wall with a pencil. Use a ruler to locate the center area between the two studs, and outline a 4-by-4-inch box on the wall. Use a utility knife to cut out this box from the wall.

2

Hold the wall plate from the mount kit over the hole, so the mounting holes rest over the studs. Drill out the holes for each of the mounting holes over the studs. Insert the lag bolts from the mount kit through the mounting holes, and tighten them into the studs with a wrench.

3

Set the TV bracket from the mount kit to align with the holes on the back of the TV. These holes and the screws used for them are known as VESA connections. Although they are small, these connections are designed to support your TV on a wall mount. Insert the VESA screws through the holes of the bracket, and tighten them into the TV using a Phillips screwdriver.

4

Cut another 4-by-4-inch hole in the wall below the TV for the wires to exit. Feed the cables down to the bottom hole, while the top of the cables hang out the top hole. Lift the TV and attach the cables to the appropriate inputs, then align the connections of the TV bracket with the connections of the wall plate. Insert the security screws and tighten with a Phillips screwdriver. Cover the bottom hole with a cable bundle wall plate, and connect the bottom ends of the cables to the electrical devices you want connected to the TV.

You only get one chance to mount a flat-screen television on the wall, so understanding how to do the job correctly is vital to the life of your expensive electronics. Bolt that TV securely to the wall like the pros do, rather than risk the sickening sound of a flat-screen TV ripping from the wall and nosediving to the floor.

Location is Everything

Before you can start drilling holes and watching television on your new set, you'll want to choose a wall and the right height to hang a flat-screen television. This is ultimately a matter of personal preference, but remember that comfort is key to long-term viewing. Video experts with the Society of Motion Picture and Television Engineers (SMPTE) say the best height for hanging a TV is about 30 degrees above the seating area in your home theater or den. You'll also want to determine the best distance from the TV to the main seating area. The SMPTE recommends a viewing distance approximately 1.6 times the size of television screen, measured diagonally. This means if you have a 65-inch flatscreen set, your ideal distance from the TV to the sofa would be 104 inches, or 8 feet 8 inches.

Prepping the Wall and Bracket

Have someone help you lift the TV into position where you want to install the set on the wall. Use a pencil to mark the area behind the wall where the mounting bracket will be bolted in place.

Find support studs behind the wall. Electronic stud finders are available at most hardware stores, or you can try the old-fashioned ( though not recommended) method of tapping on the wall with the handle of a screwdriver. If your TV weighs under 80 pounds, bolting the mounting bracket to a single stud will probably be sufficient. For heavier, larger televisions, plan on bolting the bracket into 2 studs. Whatever you do, the TV mounting bracket must be bolted directly into the wall studs. This is the only reliable way to be sure there is sufficient support for the weight of your TV set. Bolting a bracket into plaster, wood paneling or drywall without the added strength of wall studs will likely cause the bracket to pull loose in time. .

Once you've located the studs, draw an X on the wall with your pencil, then use a bubble-type leveler to measure and mark a level position for installing the mounting bracket. Hold the bracket against the wall, lining up the holes in the bracket with the X marks for the studs. You can use a pencil to make a small mark on the wall through the bracket holes for drilling the bolts.

Getting the TV on the Wall

Now that you've marked the precise anchor points for your mounting bracket, drill a hole for each bolt using a drill bit one size smaller than the mounting bolts that came with your wall-mount kit.

With a friend providing an extra set of hands to hold the mounting bracket, bolt the bracket to the wall using the supplied hardware. Attach a separate bracket to the back of the flat-screen. Use the hardware that came with the mounting kit.

Recruit your friend one more time to help you lift the TV so you can slide the smaller TV bracket over the mounting bracket on the wall. Depending on your hardware, you may need to tighten additional bolts through the bracket to lock the TV to the wall mount.

Articulating TV wall mounts are good for rooms where the seating positions relative to the display are not symmetrical or where viewing is necessary from extreme angles. Mounting to the wall in a similar fashion to standard flat mounts, articulating models can move in two directions horizontally and often have a small degree of tilt. Given the fact that these mounts are becoming slimmer, using one might be a good choice even if necessity is not immediately apparent.

Instructions

1

Find the two studs you intend to use to mount the bracket, employing a stud finder.

2

Mark the stud locations and then drill them out with the drill and bit. Use the holes on the wall mount to ease in alignment.

3

Open the mount to its fully articulated position. Insert and secure the four mounting bolts with the socket wrench.

4

Secure the TV bracket to the rear of the set by finding the four smaller bolt receiving holes. Line up the TV bracket with these holes, insert the included Allen or Phillips screws and tighten them with the appropriate screwdriver.

5

Close the articulating wall bracket to its closed position. Lift the set onto the bracket.

6

Secure any straps, bars or set screws, placed to assist in preventing the set from sliding off the mount, using the right screwdriver.

TV wall mounts are fashionable and save a lot of space in your home by eliminating bulky entertainment centers, but the key to getting the best look out of your wall mount is knowing how to hide the wires. The trick is to cut two hidden holes in the wall and run the wires through one hole into the wall and out the other.

Instructions

1

Use measuring tape and a pencil to measure and outline a 3 inch-by-3 inch hole in the drywall in the center of the area you want to position your wall mount. Measure and outline another 3 inch-by-3 inch hole at the bottom of the wall where you want the wires to exit to the devices you will hook up.

2

Cut the outlines from the drywall using a carpenter's knife. Clear away the dry wall dust and debris with your hand, then blow and vacuum out any remains with a hose attachment.

3

Place the wires through the top hole and feed them through to the bottom hole. Make sure the wires reach the device before setting up the wall mount, as it is easier to determine the needed amount of slack from the wires before the TV is up.

You can mount flat-panel TVs on walls because they weigh much less than a conventional rear-project set. To mount a flat-panel TV on a wall, first install the wall brackets into the mounting slots included on the back. The manufacturers build the mounting slots into the chassis, and the slots work in tandem with commercial wall brackets that you can purchase at electronic and audio/visual stores. The procedure is straightforward and will not harm the flat-panel TV in any way.

Instructions

1

Remove the screws that surround the wall-bracket plates on each of the two wall brackets with the Phillips screwdriver. Slide the wall-bracket plates off each of the two wall brackets.

2

Remove the screws from the two wall-bracket plates with the Phillips screwdriver. Hold the wall bracket plates with the "top" label at the top. Slide one of the wall-bracket plates into the slot on the left side of the flat-panel TV. Slide the other wall-bracket plate into the slot on the right side of the flat-panel TV's back.

3

Attach the screws you removed earlier back into the wall-bracket plates with the Phillips screwdriver. Tighten the screws to secure the plates to the back of the flat-panel TV.

4

Slide the wall-bracket plates back into the two wall brackets. Reattach the screws into the wall brackets with the Phillips screwdriver. Tighten the screws to secure the plates to the wall brackets.

Mounting an LCD or Plasma television to your wall requires that you use a wall mount sufficient for the job. Not all wall mounts are equal, though, either in their specifications or in their quality. Because of this, picking the right wall mount is essential for not only mounting the TV for an enjoyable viewing experience, but also for creating a safe mount of that won't damage the television or wall. When picking just one mount from the large variety available, you need to look at the details of each. Compare what each mount has to offer by keeping in mind your requirements, as well as your budget.

Instructions

1

Locate several wall mounts to choose from that supports not only the size of your TV, but the weight of the unit as well. Depending on the year of manufacture, the television add-ons, and the materials used, weight by size can vary drastically. Make a list of these mounts, along with kit specifications, to choose one that fits your mounting needs.

2

Check for the location of the wall studs in your wall using a stud finder. This is especially important if you've already chosen the location for your television. Check the distance between the studs with the distance between mounting holes to be certain you can use as many studs as possible. The more wall studs involved in the mounting process, the more you'll distribute the weight of the TV, leading to greater stability. Compare the locations with the mount anchors to pick a mount that has the greatest coverage possible. Remove from your list mounts that only use a single stud.

3

Determine the excess equipment necessary with the mounts you're looking at. Choose a complete mounting kit if possible, preferably one that includes the drywall anchors necessary, as well as a bubble level for leveling the mount. These parts can be purchased as add-ons if needed, but often at a higher price than when purchased along with the mount. Add in the costs of additional equipment to mounts requiring it and remove any mounts from the list whose costs are excessive due to the additions.

4

Check your mounts for adaptability once in place. Check on tilt and swivel capabilities. All LCD or Plasma televisions have limited viewing angles for full effect. You'll want to pick a mount that can change angle according to changes you make in the viewing area to avoid having to remount the TV whenever you rearrange the furniture. The greater the tilt and swivel options, the more expensive the mount is likely to be. Remove those from your list that do not fit your likely adjustment needs.

5

Pick a mount from the remaining listed mounts that contains all of your requirements, but still comes in under your budget.

One of the benefits of a flat screen LCD (liquid crystal display) television made by LG is its small form. Unlike larger CRT (cathode ray tube) or rear-projection TVs, an LCD is only a few inches thick. This makes it easy to mount onto a wall to achieve an elegant and seamless look. Although it can seem like a daunting task, mounting a television to the wall can be done in just a few minutes with the right tools.

Instructions

Instructions

1

Purchase an LCD mounting kit that lists your LG television as a supported device. Mounting kits come in all sizes, so be sure to purchase one that is made for the size of your television. Kits can be purchased at any electronics store or online.

2

Determine the area on the wall where you want to mount your television.

3

Use a stud finder to locate the studs in the wall where you want to mount the TV. If you do not have a stud finder, you can locate studs by gently tapping on the wall and listening for a hollow sound. If you hear a solid thump as opposed to a hollow, echoing thump, you have located a stud. Every mounting kit requires at least one stud in order for it to be placed securely on the wall.

4

Place the mount on the wall and use a pencil to mark where the screws will be inserted.

5

Drill small holes into the wall where mounting screws will be located. Read the manual that came with mounting kit to determine what size drill bit you should use.

6

Hold the mount up to the wall and align the holes in the mount with the screw holes on the wall.

7

Use a screwdriver to attach the mount to the wall.

8

Firmly pull on the mount to ensure that it is secure in its position on the wall.

9

Follow the directions indicated in the mounts manual to secure the LG television into the wall mount.

Wall-mounted TVs help you save a lot of space, but wiring them requires a few different steps. Cables going from media devices to the TV will need to be checked for length. Don't attach any wires until you're certain they are long enough to reach the TV when it's mounted on the wall. Cables going up and down your wall might also provide an unwanted look. Cable covers can be used to hide wires so you don't see them going up and down your wall.

Instructions

1

Remove the TV from wall. It's easier to attach cables to the TV when it's on the floor because you can see the inputs much easier. Have someone help remove the TV from the wall if it's large or heavy.

2

Attach all cables to the media devices and the TV.

3

Hang the TV on wall. Be careful not to step or get caught on any wires when you're lifting the TV up. Have someone help again if your TV is large or heavy.

4

Tie cables together using a string or with wire ties. Don't tie the cables tight; they just need to be clumped together to help you hide them behind the cable cover.

5

Attach the cable cover to the wall with the cables tucked behind. Cables should easily fit behind most covers unless you have an inordinate amount of cables. Refer to the cable cover manual for specific attaching instructions.

6

Power on the TV and media devices. You should now be able to watch your wall-mounted TV without seeing any wires running up and down your walls.

Mounting a TV on your Video Basics wall bracket might seem like a tough do-it-yourself project, but the process is actually not difficult. A good tool box is enough to get the job done. The TV mounting kit comes with all the hardware. The entire process of mounting your TV to your Video Basics wall bracket takes less than an hour to complete.

Instructions

1

Locate two vertical wall studs by running a stud finder against the wall in the area you want to mount your TV. When you find the studs, mark where they are on the wall using a pencil.

2

Hold the Video Basics wall bracket against the wall and insert the lag bolts through the mounting holes. Tighten the lag bolts into the wall studs with a wrench. The mounting bracket is now mounted on the wall.

3

Turn the TV around so you can easily see and access the back. Hold the TV bracket against the TV so its VESA holes line up evenly with the VESA holes of the TV. Insert the VESA screws through the VESA holes of the TV bracket into the TV and tighten with a Phillips-head screwdriver. The TV bracket is now mounted to the TV.

4

Take the TV over to the mounted wall bracket and line up the connections so the TV bracket fits into the wall bracket. Insert the security screws to connect the brackets.

As technology improves, flat screen TVs, such as those made by Sony, are becoming increasingly popular with consumers. One of the big advantages to a flat screen TV is the ability to hang one just about anywhere. However, without the proper hardware and installation the TV could end up falling, causing damage to the TV as well as the wall.

Instructions

1

Locate the studs on the desired wall. Use an electronic stud finder, running the finder over the wall until all the lights shine or the device beeps, indicating that you are over a stud. Mark the studs with a pencil.

2

Hold the mounting bracket up to the wall. Align the screw holes over the studs and mark the location of the holes on the wall. Check with a level.

3

Use a power drill to pre-drill the holes for the mounting screws. Use a 3/4 bit in the drill.

4

Hold the bracket back against the wall aligning the mounting holes in the bracket with the pre-drilled holes on the wall. Use the screws or bolts provided with the bracket and secure the bracket to the wall.

5

Attach the TV half of the mounting bracket onto the back of the Sony flat panel. Use the screws provided with the bracket and a Philips head screwdriver.

6

Lift the TV onto the mounting bracket. Have a friend or family member lift the TV while you guide it onto the bracket securely.

Most types of televisions can be wall mounted. More recently flat screen televisions have become popular and can be mounted to hang like a picture frame. There are many things to consider when mounting a television, including what room you want it in, how high you want it, and where the wires will go. Regardless of your preferences, there's a way to wall mount just about any televisions.

Benefits

Wall mounting a television can free up a lot of space and allow you to put a television in a very small space without using a stand or table. Flat screen televisions hang so nicely on the wall they resemble a picture frame and only stick out about 3 to 4 inches from the wall. Larger televisions can be corner mounted so they are higher and take up less space in the room. Probably the only type of television that can't be wall mounted would be a large tube big screen.

Types

There are many kinds of wall mounting hardware kits available, and the one you choose depends on what type and size of television is being mounted. For a tube television up to 32 inches, the mount has a bracket that fastens to the wall using screws, then a bar or arm that extends to hold a shelf or flat surface that the television sits on, and there are usually straps to hold the television onto the shelf. For flat screen televisions of any size, a wall mounting kit includes flat metal pieces that are individually screwed into the wall and must be arranged according to where you want the television and how you want it to hang; most flat screen televisions come ready to mount with areas on the back designed to attach to the mount. Along with the mounting hardware for either type of television, special equipment is sold separately for wire covering, and attaches to the wall below the television and runs down to the outlet so the wires slip down through the cover, which blends in with the wall.

Considerations

Television wall mounting kits and hardware can be found at most electronic stores, major general stores that sell televisions, online electronic stores, home improvement stores and furniture stores. When buying a kit for mounting a flat screen television, be sure to know the size of the television because the kits are labeled according to what size TV is being mounted. Measuring the bottom length and width of a tube television is a good idea to make sure the flat shelf on the wall mount is large enough to safely hold the television. The wire covers are sold at home improvement or hardware stores.

Function

Wall mounting kits come with very detailed instructions that should be followed to ensure the securest mounting possible. You will need a leveler and a stud finder; these can be purchased at a hardware store. A leveler is a small tool with fluid and a floating ball in it that will ensure the television is hung straight. A stud finder is a handheld tool that you slowly rub against the wall where the television is being mounted to locate the beams that you will drill into, because the drywall alone cannot hold up a television. The stud finder will sound an alarm when it has found a beam, and you will want to use a pencil to mark the beams in the wall. Once you have the studs marked, decide how high you want the television and mark where you want the top of the television to be. Now you can measure the areas on the back of the television to see how much distance there is between the attachment brackets and the top of the television. Measure down the same distance from the pencil mark you made for the top and that is where the brackets will be attached to the beams in the wall. When attaching the brackets, use the level on the top of each bracket to make sure you have it straight before using screws to fasten it to the wall. The mounting kit will have diagrams with very easy to follow instructions, and most televisions come with mounting instructions specific to that type of television. After all the brackets are in place the television can be hung or set up on the mount.

Expert Insight

When mounting a tube television, make sure to fasten the bracket and stand high enough that you can walk under it without hitting your head. When purchasing a flat screen television, make sure it is mountable, if it is, it will have areas in the back to attach to the mounting brackets. Most electronic stores offer professional mounting that can be scheduled at the time of purchase. Wire covers can be painted to match the wall and become almost invisible. You can also wallpaper a boarder over the cover or decorate it to really blend in with the wall and the room. Wall mounting a television really makes a room look classy and is a great way to avoid the clutter of a floor stand. You can put up shelves to hold other electronics that are hooked up to the television, and this really frees up space in a room.

Flat-screen televisions mount easily to a wall for a clean, professional look. The challenge, however, is mounting the flat screen TV at a height that allows for comfortable TV viewing and looks appropriate in your room.

Aim for Eye Level

The most comfortable viewing for a flat-screen TV is when it sits at eye level. Sit or stand where you will watch your TV, and mount it so the center of the screen is the same height as your eyes.

TV Cabinet

Place your television cabinet, then mount your flat-screen TV so it sits centered in the TV cabinet.

Mount Over a Mantel

A popular mounting location for a flat-screen TV is on a fireplace over the mantel.

Support With Studs

There are four bolts in your flat-screen mounting bracket. Mount your TV so all four bolts sit inside a stud. This prevents your bracket from falling out of the wall over time.

Mount a Mock First

Cut out a piece of cardboard the same dimensions as your television. Attach the cardboard to the wall and make sure you like that location before you mount your flat-screen television.

As unnatural as it may seem to hang up your TV, Phillips flat-panel TVs are made specifically to be mounted to a wall. On the back of your TV you will find an arrangement of screw holes in a box pattern. These screw holes are called VESA (for Video Electronics Standards Association) holes and they are made to connect your TV to a wall mount. Different wall mounts have different VESA dimensions so it's important to make sure the VESA dimensions of the wall mount fits the dimensions of your TV.

Instructions

1

Insert a Phillips screwdriver into the screw holes located in the middle of the back of the TV. Remove the screws and cover the TV screen with a blanket. Lay the TV screen down and pull the base out from the bottom of the TV.

2

Run a stud finder over the walls until you find two vertical studs in the area you want to hang the TV. Outline the studs on the wall with a pencil. Place the wall plate over the studs and insert the lag bolts that came with the wall mount through the corner holes of the wall plate. Use a wrench to tighten the lag bolts into the wall.

3

Lay the brackets on the back of the face down TV. Line up the VESA holes of the brackets evenly with the VESA holes of the TV. Use the VESA screws to connect the brackets to the TV. Tighten the VESA screws with the screwdriver.

4

Take the TV with the brackets connected to the back over to the wall plate. Line up the brackets to the wall plate's connectors and tighten the security screw in place. The security screw keeps the TV locked in place.

Hanging a flat screen TV on your own is a risky business. In some cases it is better to go with a professional, simply to avoid seeing your $1000 TV broken on the floor. If you are confident that you can do it yourself, then the process is actually quite simple. The two most important parts of the process are finding a wall stud for an anchor and making sure that your TV is compatible with standard TV brackets.

Instructions

1

Look for the VESA logo on your television; this will determine if it is compatible with standard hanging brackets.

2

Contact your TVs manufacturer if you can't find the logo to find out what your hanging options are. If you find the TV is VESA compatible then a standard bracket from any store should work.

3

Decide where you want your TV on the wall.

4

Search that area with the stud finder, marking out locations of the wall studs.

5

Hold the mounting bracket up to the wall to line the bracket up with a wall stud. Use the level to make sure you have the bracket level before marking the holes.

6

Mark the holes with a pencil using the bracket as a guide.

7

Drill the mounting screws into the wall; make sure they are firmly in a stud.

8

Attach the bracket that connects to your television. This process varies by TV, but usually involves screwing a mounting plate to the center of the back of the TV with four bolts.

9

Hang the TV on the mounting screws.

Types

With the rising popularity of flat panel plasma and LCD televisions, mounting them on walls rather than placing them on TV stands has become an accepted practice. The mounts themselves are fairly simple, straightforward devices. They are traditionally solid, heavy pieces of metal that screw into both the wall and the back of your television. There are two kinds of television wall mounts on the market. There are ones that simply "hang" your television on the wall like a picture frame, and there are ones that swivel from side to side like you would see in a hospital room.

Logistics

How the television wall mount "works" is actually a simple concept. It is actually very similar to the process one would go through to hang a picture in a fame that is heavier than average. The mount itself firmly nails into the studs of your wall. A television is a large, heavy (and most importantly expensive) object, and it will need the stud to support its weight. Studs in general are designed to be load-bearing, which makes them ideal for the hanging of heavy objects. When the mount is on the wall, a series of screws and brackets attach to the back of the television to secure and lock it into place. This ensures that the television will not move from the mount. The mount is securely attached to the wall with a similar series of screws. The weight of the television is now supported by the mount. This is secured to the stud of the wall.

Swivel Mounts

Swivel mounts are ones that operate exactly how they sound. Instead of being in a fixed position, the user can "swivel" them from side to side, changing their direction at will. A swivel mount installs and operates essentially the exact same way as a regular mount. The only difference is the addition of a mechanical "arm." They screw into the wall stud. The mount has the arm that juts off of it. The arm is what attaches to the television, and it is also what allows you to change the direction.

Current trends Flat Panel LCD and Plasma HDTV's are making TV's thinner, lighter and more powerful. Superior high definition viewing, affordable pricing with added space and energy savings are only just a few practical reasons for purchasing a new HDTV. With newer thinner designs, LCD and Plasma HDTV's are ideal for wall mounting. Wall mounting your television frees up space and adds a new element of aesthetic appeal to your home theater.

Positioning

Before getting into any hardware mounting, find the best possible position to mount your television. Because wall mounting an HDTV is more of a permanent solution, careful planning is needed when integrating the television into your home design.
Furniture placement, overall themes, viewing angles, and the best audio positioning are all factors that will help determine the placement of the LCD or Plasma TV.
Once you have decided the general positioning of the wall mount installation, cut out a piece of cardboard or wrapping paper in proportion the size of the flat panel television. Next, approximate the placement by taping the piece of cardboard or wrapping paper to the wall where the TV will be placed and mark it with a pencil.

Preparing the TV

Remove the stand from the television and lay the TV on its face. Locate the four mounting holes on the back of the television and remove the bolts. Next, remove the mounting arms or mounting plate from the wall mount packaging.
To attach mounting arms, line up the arms vertically and parallel to each other using the mounting holes on the back of the television. Make sure that they are in perfect alignment and bolt the arms using the bolts and washer supplied with the wall mount.
If you are using a mounting plate, simply line up the holes with the mounting holes on the television. Secure the mounting plate with the bolts and washers included with your wall mount.

Preparing the Wall

Locate the studs closest to the desired position using a stud finder and mark them with a pencil. Remove the wall mount from the package. Line up the wall mount up to the studs within the center of the marked position you determined earlier. If it is not perfectly centered, wall mounts can be adjusted horizontally at a later time.
Using a level, line up the wall mount and mark the positioning of where he bolts will go. Drill holes into the stud about 1" deep, drill bit size depends on the size of bolts supplied with the wall mount. Bolt the wall mount to the wall with bolts and washers, but don't tighten down the bolts completely. Adjust the position of the wall mount left or right to center it to your desired position. When you are done, tighten the bolts the rest of the way.

Mounting the Television

Attaching the television to the wall mount takes two people. Simply lift the television and hook it to the wall mount. At this point you can further adjust the positioning horizontally to center it perfectly. Once the desired position is acquired, tighten down the screws that attach the mounting arms or plate to the wall mount.

An articulating TV is a TV that is connected to a wall mount with extended arms that allows you to move the TV into several different positions. There are many different types of articulating mounts on the market. You can even find models that can tilt upside down or spin a full 360 degrees. The model you have and the amount of space around your TV will determine the versatility of you articulating TV. How to install your wall mount will depend on the instructions for your specific model. Most mounts use a similar method for installation.

Instructions

1

Decide where you want to put your TV. You want to choose a spot that will allow maximum mobility for your TV. Make sure the area where you plan to mount your TV is free of any obstructions and has an electrical outlet nearby.

2

Locate the wall studs in the wall where you would like to hang the TV. To find the wall studs, run a stud finder across the surface of the wall. The stud finder will light up when you hit the stud. If you don't have a stud finder, you can knock on the wood and listen carefully. You will hear a hollow sound where the wall is hollow and a dull sound when you knock on the stud. Mark the center of the studs with a pencil.

3

Hold your articulating mount up to the wall studs and drill it into place. You may want to ask a friend to hold the mount while you drill it in. Make sure to use a level and ensure that the mount is even before you drill it into place.

4

Connect the mount rails to the back of your TV. Each mount comes with a set of rails that connects to the back of your TV. Just simply drill the rails into the holes on the back of your TV.

5

Connect any cables to your TV. A lot of connections (DVD player, gaming console, etc.) are in the back of the TV so they will be hard to plug in after the TV is mounted to the wall.

6

Slide your TV into the articulating mount. This also easier with a helping hand. There will be a tension screw on the mount that you can hand tighten to secure your TV.

Though it may seem like a simple task, there is some degree of "handy man" skill required to properly install a television wall mount. Keep reading to learn how to increase your viewing pleasure in short order.

Instructions

1

Decide where you want to mount the TV. Identify the location of wall studs able to support the weight of the television. A stud finder is a useful tool for this process. Mark the studs with a pencil as you locate them.

2

Level the bracket before you anchor the television wall mount to the studs. This is a two-man job, as your partner needs to hold the bracket steady while you attach it to the studs with screws. Double check the level and make any adjustments before you place the screws.

3

Attach the portion of the wall mount designed to fit onto the television to the back of your set by way of the mounting holes. The holes might be covered, but you can easily remove the covers using the flat edge of a screwdriver.

4

Hang the television on the mounting bracket you've already attached to the wall. Have a partner hold the television in place while you screw the two brackets together.

Mounting a hanging plasma TV set is a bit trickier than mounting other big flat-screen sets. A plasma TV uses inert gases to produce the picture, and the positioning of the TV set affects how these gases work. Many retailers that sell plasma TVs offer professional installation, but it is possible to mount one of these TV sets yourself.

Requirements and Restrictions

Because of the gases used inside a plasma TV that help generate the electricity for the image, the TV cannot be hung at a 45 degree angle or greater. Also, the gases can cause interference with infrared signals, meaning you may find it hard for any universal remote controls to work. The TV set's remote control is designed to overcome this, but any remotes for other devices may have problems. Placing the set above a fireplace or other device that generates heat is not good because the heat can damage the set over time. If the set includes channel speakers, you'll usually need clearance of twice the screen's width to make room for both the TV and its speakers.

Positioning

The best minimum viewing distance for a plasma TV set is twice the size of the screen. (Remember that the screen is measured in inches, so divide that measurement by 12 to get it in feet.) Once you know the optimum distance, use it to figure out the best height for hanging the set. Place a sheet of plywood or cardboard on the wall and see if you're comfortable seeing the screen while sitting at the recommended distance. Also, take windows and sunlight into account. If the light from the windows will create a glare, you might need to find another location or look into curtains to block the sun.

Installation

A wall mount is the best option for a non-professional to hang the TV set. Remember that the mount must be screwed into the wall studs. A ceiling mount is another option, but this is best left to professionals who can gauge the strength and integrity of your ceiling. If you want to conceal any cables, your best options are running them through a tube (especially if it's the same color as the wall), sending them through a hole in the wall (if it's drywall only) or prying up the baseboards to store the cables underneath.

Wall-mounted LCD televisions are becoming more popular and prices continue to fall as technology advances. Amazingly, LCD screens are now available in as large as 100-inches diagonally. However, the cost of most large-sized LCD televisions remains relatively high compared to their analog counterpart. Luckily, there are ways to reduce the price of having a wall-mounted LCD television.

Computer Monitor

LCD computer monitors are significantly cheaper than LCD televisions. An LCD computer monitor can easily be modified into a television. An LCD computer monitor is essentially the same as an LCD television and picture quality is comparable. LCD computer monitors can also be mounted to a wall with a simple mounting bracket.

Refurbished

A refurbished LCD television is a good option for those not looking to break the bank with a new television. Refurbished televisions are just as good as new ones and often come with an extended warranty. The major difference between a refurbished television and a new one is the price. Refurbished LCD televisions can be several hundred dollars cheaper than new ones.

Used

A used television may also be an excellent alternative to a new LCD television. A used model is significantly cheaper than brand new one. The television may only be one or two years old and cost less than a few hundred dollars. Sites like eBay, Craigslist and other classified ad websites are excellent resources for finding used LCD televisions. Always research prospective models before buying.

Generic Brand

A generic brand LCD television is another way to obtain an LCD television for a low cost. Brands like Sony, Sharp, Panasonic and Samsung are well known for their LCD televisions. However, there are a number of lesser-known brands that are not carried by many of the big box stores, such as Vizio and Westinghouse. Check smaller electronics retailers to find other brands that can be significantly cheaper than the name brand LCD television.

Existing Stand

Using the existing stand for an LCD TV instead of using a wall mount can help greatly reduce costs. Prop the stand on a table, book case, or construct a stand. It is not the same as a wall mount but the TV can be the same height and the viewer can save some money by doing this.

Generic Mount

LCD wall mounts for specific model LCD televisions can be expensive. The manufacturers want the viewer to buy the LCD mount designed by them for that TV. However, using a generic mount purchased at a hardware store can also work. A generic mount, not necessarily designed for that specific model television, can be significantly cheaper and work just as effectively.

Flat screen televisions are quickly taking over homes across the country. Not only do most flat screens pride themselves on vibrant picture quality, but are also slim, making them easy to put on a shelf or TV stand. Another benefit to flat screen televisions are the fact that they can be mounted to the wall of your home to be even more space efficient.

Instructions

1

Measure your television using a measuring tape. Once you have done this find a place within your home that will fit your television's measurements. Use a stud finder to locate a stud on which you will mount the television in the area that you have chosen. A stud on the inside of the wall will allow the hanging of the television mount to it, otherwise without the stud, you'll need to find another appropriate area. Make a mark using a pencil when you have found the stud.

2

Choose an area close to an outlet. Some people are concerned that wires hanging from their television to the wall outlet can look cluttered or sloppy. Purchase a cord cover or some other type of cord concealment or hire an electrician to run the flat screen's cord through the inside of your wall to an outlet.

3

Attach the mount to the flat screen television. Each television mount will have its own specific directions--screws and a screw driver, or alternately a drill, are needed to install the mount. Most television mounts require the installation of two short beams to the back of the television.

4

Attach the television mount to the wall. Before screwing the mount to the wall, have a friend hold it up against the wall, while you stand back and ensure that the position is where it is preferred. Ideally the mount should be at eye level from the position you view the television. Ensure that the area in which you install the mount is on the stud mark that was made earlier. Once satisfied with the placement, trace the area with a pencil.

5

Put the mount back on your wall and hold it there as your friend checks for level. Adjust the mount accordingly if it is not. Screw the mount into the wall. Check again to make sure it is level. Hang the television onto the wall mount with the assistance of your friend. The television should easily connect with the mount because of the two beams that were installed earlier onto the back of it. After mounting the television, check once again for level. If all is well, put away the tools and enjoy your new wall-mounted television.

Mounting a plasma TV on the wall may seem a bit challenging at first, but it's not that difficult. All you need are a few simple tools, a proper mounting kit and someone willing to help with the heavy lifting. Follow these steps to find out how to mount a plasma TV on the wall.

Instructions

1

Find the best location on the wall to mount the plasma screen. Consider how much room you may want on that wall, especially if you plan on mounting a speaker system as well.

2

Buy a mounting kit. You can buy mounting kits online (see Resources below) along with other online retailers. Make sure your kit and plasma TV are VESA compatible so that you'll have standard measurements and so that you'll be able to attach it quickly and easily once you're ready to mount it.

3

Check to see if you have the tools required to mount the TV. You'll need screwdrivers, a socket set, a drill and a measuring tape. A stud finder with a built-in level is helpful to find the wall studs for secure bolt placement.

4

Locate the studs. You should use two wall studs to support the weight when mounting the plasma screen. Secure the mounting rails to the back of the plasma screen. You may also want to pre-drill the holes for the wall anchors.

5

Cut the hole for the wires to come through by using your box cutter or a drywall saw. If you don't want to drill additional holes in the wall for the wires, you can buy cable brackets that will route the wiring in a corner of the room.

6

Drill the holes for the mounting anchors. Make sure that the anchors will secure the mounting bracket to a wall stud and not just the drywall.

7

Secure the mount to the wall. Use a socket wrench to get those anchors locked down tightly. These bolts will be supporting the whole weight of the TV. Protect your investment by ensuring that the bolts are properly anchored into something solid.

8

Grab a friend or family member to help you put the plasma screen onto the wall mount. Have them support the weight while you bolt the mounting rails to the mounting bracket. Make sure that it's secure and that the screen is ready to go.

Flat panel mounts consist of two core components; the wall bracket, and the TV bracket that attaches to the set. When both pieces are combined on the wall, the image of what most picture as the quintessential flat panel installation begins to take form. Placing the set on a wall bracket frees up floor space, increases viewing accessibility, and enhances the slim form factor of the set. Most of the required hardware is included with the mounts, speeding up the installation process.

Instructions

1

Locate two studs on the proposed mounting wall. Holding the wall bracket against the wall, mark through at least four bolt holes with the tip of the drill bit into the studs.

2

Drill out the marked locations with the 3/16 inch drill bit.

3

Place the wall bracket back against the wall, and drive the included lag screws and washers through the mount into wall studs with the ratchet and socket set.

4

Set the TV bracket against the back of the TV, aligned with the brass-colored inserts. Screw in the included screws with the supplied tool.

5

Lift and hang the set onto the wall bracket. Tighten any security screws on the mount with the included hardware.

A good way to clear up some space in your living room is to mount your flat panel television to the wall. Depending on where you place the TV, you may want it to remain stationary, or you may need an adjustable viewing radius. Regardless of which type of bracket you desire, a handful of brackets are considered the best.

Low-Profile Brackets

This is your basic wall mount for an LCD or Plasma flat panel television. The main function is simply to secure the TV to the wall in a stationary position, rendering it nonadjustable. A few cater to smaller flat panels; however, the majority of them are built with 32-inch televisions and larger. More innovative brands have built-in shelving systems for a few electronics; the shelves hang directly below the television on the same wall mount. Some of the most trusted brands for stationary, low-profile brackets are Bush Industries Furniture, Sanus, BDI Vista, Premier and Level Mount.

Tilting Brackets

A tilting wall bracket will mount the flat panel TV securely to the wall, as the low-profile model will, but has an additional function. The top of the television can pull out from the wall, providing a tilted view of the TV. The majority of the tilting brackets are built with 32-inch and larger TVs in mind. Going with brands like Level Mount, Premier, Chief Fusion, and OmniMount will ensure that you get the best tilting bracket for your money.

Articulating/Swiveling Brackets

Providing the most functional method to view your flat panel television is the articulating wall bracket, which mounts your TV to the wall via an articulating arm that pulls out and adjusts to face left or right of the viewing radius. These are typically built for flat panel televisions 32-inch and larger. Due to the additional moving parts, you must get one of the best-rated swiveling brackets to avoid any television tragedies. Peerless, OmniMount, Sanus and SpaceSaver are some of the best-rated brands.

A plasma TV is thin enough to be mounted to your wall. Plasma TV sets often come with wall mounting kits. If your TV did not come with this wall mounting kit, then you will need to purchase a flat TV panel mount, which can be found at most electronics stores. Once your plasma TV mount is installed and the television hung, you will be able to enjoy countless hours of shows and movies at the perfect viewing level.

Instructions

1

Figure out the best height to hang your plasma TV. This generally depends on the seating in your room. Sit on the couches or chairs that will be in front of the TV to help you decide. The middle of the screen of your plasma TV should be at approximately eye level.

2

Use a level to mark a straight line on the wall with a pencil. This will ensure you install the plasma TV wall mount straight.

3

Use a stud finder to locate the studs in your wall. If you don't have a stud finder, look for nearby electrical outlets or switches. These will be anchored to studs. In most homes, the studs are spaced every 16 inches. To make sure the stud is there, drill a hole using a power drill. If you feel resistance, then there is a stud. You must mount your plasma TV to the stud or it will fall off the wall.

4

Place the wall mount against the wall and match it up with the straight line you drew. There will be four holes where screws will be attached to the wall mount. Mark these holes on the wall with your pencil. Make sure you're marking spaces over the wall studs you found.

5

Use a power drill to drill starter holes into the four places on your wall that you marked. If you have standard wall studs, use a regular drill bit. For metal studs, use twist bits. These will go through steel.

6

Hold the wall mount back up to the wall and use a power screwdriver to attach it with the four screws that came with your mount if you have standard wall studs. For metal studs, use toggle bolts. The TV can now be slid onto the mount. Your plasma TV should have a mount already in place that can slide onto the wall mount.

Mounting a LCD television provides a different look to your home entertainment system. It can create more room in the room by possibly eliminating the television stand. When mounting the television to the wall the height must be considered to ensure a comfortable viewing experience.

Wall Mount

Determining the correct height to mount the television can depend on the type of mount being used. A titling wall mount will give you more installation options than a standard flush wall mount. A flush wall mount will not allow the television to be angled or moved and it stays fixed in place.

Mounting Height

Crutchfield recommends mounting the television with the center of the screen at your eye level when seated. It can also be a little higher than eye level but not by much when using a flush mount.

Mounting Height with Tilting Mount

Mounting the LCD using a titling wall mount gives you more flexibility as the angle can be adjusted for the television. The television can be placed higher if preferred and the screen then angled to allow comfortable viewing from a seated position.

Mounting a flat screen TV is relatively simple as long as you know what your options are and purchase the appropriate size and style of mount for your television. There are four basic types of mounts, and each one comes in various sizes to fit most television designs.

Considerations

Most mounts consist of two main parts---the part that is fixed to the wall and the part that connects to the back of the television. Before you buy your TV mount, check the owner's manual of the television for information about appropriate mounts. You can also go by the information on the mount package itself.
In most cases, you install the wall plate first by finding a stud to anchor it to. If you have a very large mount, you may need to use two studs.
Next, you attach the second part to the back of the television. Most flat screen TVs are set up for mount attachment, so this shouldn't be very difficult.
The television should then be ready to hang on the wall plate. Always read and follow the directions that come with the mount, as each model has different steps and variations. Failure to follow the instructions could lead to damage to the television and even injuries.

Types

The four main types of flat screen mounts are flat, tilt, swivel, and ceiling.
In a flat mount, the television is attached to the wall plate and usually extends about one inch from the wall. Once installed, it does not move.
The tilt mount allows the screen to be tilted up and down.
The swivel mount can also be tilted, but the television is attached to an arm that allows for it to be turned right or left as well.
In a ceiling mount, the plate attaches to the ceiling and the television is attached to an arm that hangs down. It may or may not be able to tilt or swivel.

Potential

The main advantage of the flat or standard mount is that the TV sits very flat against the wall, often only extending about an inch. It can be used for any size flat screen television, and is most appropriate for rooms in which the screen can be seen from entire viewing area. The main disadvantage, of course, is that the screen does not move, so anyone sitting on the side or too close to the floor may not be able to see the screen.
The tilt mount allows you to tilt the television. In most, you just push the screen up or down. There are some designs, however, that require a tool (usually supplied) to move the screen, which is much less convenient. The tilt mount can be used for almost any size flat screen television and is appropriate for most room sizes. Like the standard mount, anyone sitting too far to the left or right of the screen may not be able to see the picture.
Swivel mounts, also known as articulating mounts, are excellent for large rooms because they allow the screen to be seen from virtually any angle. The main complaint about this kind of mount is that the television is not flat to the wall---the arm causes it to stick out quite a bit (distances vary). However, if it can be strategically mounted close to a corner and turned in the appropriate direction, this may not be a significant problem. A variation of the swivel mount allows the television to be turned up or down at a ninety degree angle. This people who are lying down close to, or underneath, the television to see the screen.
Ceiling mounts are good for very large or irregularly shaped rooms and are popular in public settings.

Expert Insight

When mounting a television, you have to deal with the various power cords and cables. While you can leave them hanging in the open, most people prefer to conceal them them. One way is to buy a cord cover and paint it to match the walls. There different kinds of covers, some that stick over the cables, and others that are actually nailed to the wall. One of the disadvantages of using a cord cover is that you cannot easily add or remove connections to the television---you have to reinstall and, most likely, repaint the cover.
The most popular option for hiding the cables is to drill two holes in the wall, one behind the TV and one near the floor. You then feed the cords are through the top hole run them down the wall and through the hole by the floor. This way the cables are completely hidden and you can add or remove them with ease. The main disadvantage of this option is that you will have two holes in the wall that will be noticeable if you decide to move the television to another location.

Warning

Purchase the right size mount for your size television. In general, smaller TVs can be safely used with any of the types of mounts. Larger televisions must have sturdy mounts because of their weight. Swivel and ceiling mounts available for larger televisions, but these usually have two arms and are designed to be well-anchored into two wall studs.

LCD technology makes larger TVs a more common sight in households and businesses. The weight reduction in these TVs, made possible by the manufacturing technology, enables you to mount them to any stable wall containing wall studs. You can successfully mount a TV of any size using the proper mounting materials. Once it's on a mount that allows for movement, you can adjust the TV in place, tilting it from side to side and swiveling a full 90 degrees so that you can watch the picture in portrait mode.

Instructions

1

Find a wall mount that's compatible with your TV size and brand. Look for one rated as VESA compatible, as these will fit most LCD TVs. Check with the TV manufacturer for the weight of your TV and make sure that the mount can secure the weight necessary. Also check that the mount holds the TV slightly away from the wall and provides you with the amount of side to side movement and swiveling capability you need.

2

Use the stud finder to locate the wall studs in the area where you wish to mount the TV. Mark the stud locations with a piece of chalk.

3

Attach the mounting rails in the kit to the rear of the TV. Screw the rails in place.

4

Set the mount onto the wall. Center the mount so that can attach to as many wall studs as possible. Mark the anchor holes in the mount on the wall with chalk. Place the holes so that they fall on the center of the wall studs for the most security. Use the carpenter's level to ensure that the mount is level on the wall. Remove the mount and set it aside while you drill the pilot holes.

5

Drill the pilot holes in the areas marked for your anchor screws using the electric drill. Drill the holes with a drill bit slightly smaller than the anchor screws contained in the kit.

6

Secure the TV mount to the wall, screwing it into place with the anchor screws. Use the pilot holes drilled earlier to start the screws and make sure to attach the mount tightly to the wall. Check the mount for movement, tightening screws where necessary.

7

Mount the rails on the rear of the TV to the mount secured to the wall. Large LCD TVs can be more than 100 pounds, so get a helper to aid you in raising and mounting the TV. Slide the brackets on the rails onto the mount and then lock the TV into place using the safety tabs.

8

Connect the display and power cables to the TV and then connect the TV to a picture source and plug it in. Turn on the TV and test that it turns from side to side and swivels in place without obstruction from the attached cables. Adjust the TV to a preferred angle for viewing.