Sanus Wall Mount

Mounting your LCD flat screen television on your wall not only looks stylish, but also opens up some extra elbow room in your living room, bedroom or den. Though an LCD television is flat enough to hang on the wall, it's considerably heavier than your average framed picture or wall art. You'll need a mounting bracket and a suitable solid place to attach it to the wall.

Instructions

1 Remove the base from the television if it's not already off. Locate the mounting holes on the back of the television and measure how far apart they are. There are probably four of them, two on either side of the back of the set. Write down the measurements and go to the electronics or hardware store. Either should have a selection of suitable television wall mounts in the section where they sell antennas, TV cable and connectors.
2 Buy a mounting bracket that fits your television. There are two basic styles of mounts. One pulls the television flat against the wall or gives it a slight downward angle for viewing. The other mounts the television on an extension away from the wall so that it can be turned to get multiple viewing angles. These extended mounts work best for corner-mounted televisions.
3 Set up your television against a wall and determine the limits of its viewing angle. Consumer Reports notes that LCD televisions' optimal viewing angles vary from set to set. Some may lose brightness depending on the angle, while others are more vulnerable to up and down angles. An extended mount might be more appropriate to sets with poorer side-angle viewing since you can pivot them on the mount toward where most of the viewers are sitting. For up/down angle viewing quality loss, a wall mount that angles the screen downward slightly toward the viewer works better. If the LCD screen picture remains clear enough to cover all the viewer seats in the room, simply hang it flat on the wall.
4 Find and mark the wall studs in the area where you want to hang the LCD screen. Pass the stud-finder back and forth over the wall and watch for the indicator to jump. It may take several passes. Most stud-finders look for nail heads that are spaced up and down the wall under the plaster.
5 Push the wall mount bracket or brackets up against the wall and align the screw holes with the marks for the studs. Screw the bracket into the wall with a 3-1/2 inch screw with a washer behind it. Make sure the screw bites into the underlying wood stud. If all of the mounting holes cannot reach into a wooden stud, unscrew all the screws on the mount. Drill a quarter-inch hole through the plaster or panel behind the mounting hole. Push a toggle bolt with a flat washer through the mounting hole on the wall mount. Screw the spring-loaded "wings" of the toggle bolt onto the very end of the bolt. Push the "wings" through the hole till they clear the wall and extend, then push the wall mount flat against the wall and tighten the toggle bolt with your drill's screwdriver bit. Do the same on each hole that doesn't reach a stud. Redrive the screws that do reach the stud behind the wall. At least half the mounting screws should be into a solid stud to carry the weight of the television.
6 Lift the television onto the wall mount brackets. There will be a simple secondary mounting bracket that screws into the mounting holes on the back of the television or the set will have wall-mount holes or openings molded into the back of the case that fit onto the wall mount. The television should lift onto the wall bracket and mount securely. If the bracket swivels left or right, up or down, there will be a set screw or wing nut to secure the mount from moving. Adjust the television to the optimal viewing angle and tighten the set screw or nut. Attach the cord to the television and run it to the nearest wall socket. Cover the cord with decorative trim if desired.

Wall-mounting DirecTV receivers on specialized equipment shelves makes sense in places where adding A/V furniture is either impractical or impossible. This often is the case in bedrooms, kids' play areas and kitchens, where floor and counter space is at a premium. Although these shelving options have been around for quite some time, their popularity has increased as more people mount flat screens on the wall. Mounting small components is really not much different than hanging a heavy shelf and requires basic tools.

Instructions

Hang out

1 Locate a stud in the desired mounting area using the stud finder. Hold the wall bracket against this location and mark four holes on the wall through the bracket with the drill bit.
2 Set aside the wall bracket. Drill the four holes marked previously, ensuring that the stud's center is being hit in the process.
3 Return the wall bracket to the wall. Use the supplied bolts and the socket wrench to secure the bracket in place. Use the level to ensure the mount is straight prior to tightening the bolts fully. (There should be enough play in the bolt holes to make minor adjustments.)
4 Insert the U-shaped shelf in the wall bracket in the supplied receiving areas. Secure the insert into the receiving area with the small supplied screw and Allen wrench. Snap over the cosmetic trim piece to cover the the wall bracket and tap the two cosmetic end caps into the ends of the shelf with the hammer.

Nowadays, technology is growing, to the electronic media that we often use to obtain information also develops like television, ranging from the broad shape to the slim form factor, which is wasteful of energy to energy-efficient, which is now in the presence of television began to lean such as LED or LCD television, even saving space for the owner, especially if you put it on a wall bracket and put it in the living room, family room, bed room and other rooms as needed owners.

Installing the bracket is easy to hard, easy it is when you just put the TV on the chassis bracket, difficulty when having to bother to drill and measure the balance and accuracy in the beginning before drilling in the wall of the house.

Here we would like to share a bit of how the television on the wall mounting bracket for LED TV / LCD that might be useful to readers, before there is some equipment that you need to prepare, among other things:

1. Bracket TV
2. Ruler
3. Pencil
4. Drill
5. Screwdriver with size in accordance with the nut provided in the bracket

For the installation method, first used to estimate the size of the television you currently want to display in a measure of how high the wall, or can use a ruler to measure the height of how long to expect from the floor to the bottom upwards, then to the bracket that has the advantages of DOF (degrees of freedom such as dual arm that can reach out to the right and left with more extensive) try not blocked cupboard or the like objects.

Once you have determined the proper position, hold the bracket in position (make sure the position is correct) and then use a pencil to mark the holes provided on the bracket to the wall, mark with a pencil and filled in the hole to form streaks corresponding holes with bracket.

After marking the wall is completed, you are able to prepare your drill machine and start drilling the wall that has been marked. Before drilling, drill bits select the closest size of the hole and the size of the plastic nails (a kind of white plastic that will be incorporated into the wall, the retaining bracket function is as a television which will be paired with nut to hold the bracket in order not to fall) that is provided on the bracket (usually bracket is included in the packaging).

When you have started to drill try not too shallow or too deep, you can estimate the length of the plastic spikes with a depth that has been penetrated by the drill bit. Do not forget you have to clean up after drilling the borehole so as not to disturb it later when you pair a plastic nail into the wall, you can clean it using the drill bit by pulling out the dust.

Once you successfully perform drilling, it's time you put a bracket on the wall, you first need to install (enter) first nail into the plastic of the wall, after that you can install steel / iron retaining bracket (varies, depending on which bracket you are using) then followed with a nut to lock the holder into the plastic spikes.

After successfully retaining bracket is installed properly, you are able to rely on the retaining bracket arm with safe, you do not have to worry about your TV bracket and fall if you've set it up properly and does not exceed the maximum limit of the bracket (usually written on cardboard bracket). Do not forget to lock the retaining bracket (if any) to ensure the position of the bracket will not move or fall when bumped.

For bracket that attaches to the TV, make it more secure, you can set it up before the retaining bracket mounted to the bracket, so that when the television is already attached to the bracket you can easily put the television safely and comfortably in the bracket and you can enjoy watching a favorite television broadcasts you are.

Similarly, we can convey information, may be useful and helpful.

Magnavox flat-screen LCD TVs offer two separate means of installation. A base that can be attached to the bottom of the flat screen comes in the box with a Magnavox LCD when you buy it, and Magnavox flat screens also provide screw holes on the back that can be used to mount the TVs with a compatible wall mount. Mounting the Magnavox LCD flat-screen television can save space in your home by eliminating the need for a TV stand.

Instructions

1 Get a wall mount that fits the size and weight specifications of your Magnavox LCD TV. Wall-mount kits list on the packaging the maximum dimensions and weight of a television that the mount can safely support.
2 Mark the wall where you want to hang the Magnavox LCD television. Crutchfield states that you should hang an LCD TV so that the middle of the screen is approximately eye level when you sit down to watch television. Therefore, you should measure the distance from the floor to eye level when you sit on the couch or other main seating in the room with a measuring tape and then add a few inches to that measurement to determine where the top of the screen should hit. Next, measure that distance up from the floor and mark several places across the wall where the top of the screen should hit.
3 Find the studs in the wall with a stud finder. Next, find the middle of each stud. Crutchfield recommends finding the stud center by tapping a nail into the wall where the stud is located until the nail hits the stud, removing the nail and moving it over inch and tapping it in again. Do this in both directions across the stud and, when you find nothing but drywall on either side, measure the distance between the holes and mark the middle.
4 Measure between the screw holes on the wall bracket part of the TV mount. Transfer the distances between the screw holes on the mount to the wall, marking the location where each screw should go and trying to keep the screw locations in the center of the wall studs whenever possible. Screw the bracket into the wall using the screws provided with the wall mount.
5 Attach the TV bracket part of the wall mount to the mounting holes on the Magnavox LCD TV. To attach, simply use the screws provided to screw the bracket into the holes. Once both parts of the wall mount have been installed, lift the bracket on the LCD TV up and over the wall bracket and lower the TV until the brackets of the wall mount lock into place.

Mounting a TV to a wall has become standard fare, thanks to lightweight flat-panel LCD and plasma televisions. You can mount a TV to a striped wall, providing you have purchased a TV wall-mounting kit from an electronics store or a home and garden shop. The backs of LCD and plasma televisions employ a standard mounting scheme, so any brand-name wall-mounting kits can be used. A few household tools will be needed as well.

Instructions

1

Measure the width between the two grooves on the back of the TV that the TV brackets from the TV wall-mounting kit will be attached to -- use a tape measure to do this.

2

Place a dot on the wall with a pencil at the height where you want the TV to be. Measure across from the dot on the wall using the tape measure. Make another dot on the wall where the measurement that was taken from the back of the TV is reached.

3

Place a stud finder against one of the dots on the wall and move it left and right until the needle twitches, indicating a stud. Make an "X" at this point with the grease pencil. Repeat this procedure at the other dot on the wall.

4

Place the TV wall bracket against the striped wall, with the holes in the bracket lined up with the dots made on the wall. Partially screw in a metal screw in the two dots on the wall with a power drill screwdriver.

5

Place a spirit level against the top edge of the bracket. Adjust the bracket so that the bubble in the spirit level is evenly between the two lines on the information panel. Screw the two screws all the rest of the way in. Screw in metal screws through the other holes in the bracket.

6

Place a TV frame from the TV mounting kit into each of the two grooves on the back of the TV. Screw metal screws through each TV frame into the back of the TV using a Phillips screwdriver.

7

Lift the TV and insert the TV frames into the grooves in the TV wall bracket. Tighten the set screws to secure the TV frames in the bracket.

To take advantage of a flat panel TV's slim design, wall mounting is the choice for a high-tech, space-saving decor. There are plenty of options for purchasing a wall mount, but another option is to build one yourself.

Instructions

1

Trim the horizontal bracket to a length slightly smaller than the width of your TV.

2

Cut the vertical bracket into two pieces, each measuring about 12 inches.

3

Cut a notch into each end that is identical to the factory-cut notches at the other end. You now have two vertical brackets with two notches in each of them.

4

Line up the vertical brackets with the screw mount holes on the back of the TV, and mark where you need to drill for the screws to fit.

5

Place weather-strip on the side that will mount to the TV.

6

Place weather-strip on the thicker side of the horizontal bracket that will be attached to the wall.

7

Find the stud in the wall and screw one screw into the stud. Find the second stud and mark where you need to drill for the second stud screw. Drill the hole for the second screw.

8

Place the horizontal bracket against the wall, and mount with large grabber screws.

9

Now the horizontal bracket is attached to the wall. Next, attach the vertical brackets to the TV.

10

Screw the vertical brackets onto the back of the TV and slide them under the lip of the horizontal bracket until it fits in the slot. Hang the TV.

LG flat panel televisions, to many owners and interior designers, look their best when wall-mounted. LG sets support the VESA or Video Electronics Standards Organization mounting protocol. This means that for the installer, selecting virtually any compatible mount is the correct option, depending on the installation requirements. LG TVs offer a variety of size options, all capable of wall mounting. Regardless of the size or installation, LG sets offer slim aesthetics, ideal for wall mounting.

Instructions

1

Move the stud finder along the intended mounting wall. Locate two studs and mark their locations with the tip of the drill bit.

2

Place the wall bracket half of the wall mount against the wall, in concordance with the marked studs. Drill through at least four of the bolt holes with the 3/16-inch bit.

3

Insert the included lag screws and washers through the wall bracket and into the drilled holes. Tighten them fully using the socket wrench and inserts.

4

Locate the inserts on the rear of the LG set. These are gold-colored threaded metal inserts, designed to accept the included Allen bolts. Align the TV bracket with these inserts.

5

Insert the included Allen bolts through the holes in the bracket, tightening them securely with the included Allen key.

6

Lift the LG set onto the wall bracket, using an assistant if necessary. Align the TV using the level. Tighten any securing set screws using the Allen key, included with the mount.

Flat screen LCD televisions have amazing space-saving capabilities and use less energy than older CRT televisions. Typically, LCD televisions come equipped with a stand that will allow you to position it on a flat surface such as a home entertainment cabinet. Mounting LCD televisions on a wall requires you to purchase and install a special wall mount for a safe and sturdy fit. Larger LCD televisions should be mounted with the aid of an additional person.

Instructions

1

Take both the LCD television and the wall mount accessories out of their boxes. If your television came with the regular stand mounted on the bottom, remove the stand according to your television's documentation with an appropriate sized screwdriver.

2

Determine the mounting location for the television and decide how you are going to run the audio, video and power cords to your television. Have a qualified electrician install a new electrical outlet as well as any other home theater wiring inside the wall for a cleaner look. Alternatively, you can purchase and install a wiring loom on the outside of your wall to hide your televisions wiring (these wiring hiding looms are typically flat and can be painted to match your wall).

3

Install the two metal brackets that came with your wall mount kit on the back of the TV. These brackets are long, channeled and feature multiple holes for you to choose from so you can mount them to different brands and TV sizes. Your mounting kit will come with different sized bolts or screws; you must find the appropriate size that will screw into the holes used for a TV mount on the back of the LCD television.

4

Double-check the tightness of the mounting brackets installed on the back of your TV. Make sure the brackets are evenly spaced from the top and bottom portions of the television. Install the two hooked bracket hangers on the mounting plate temporarily (the mounting plate resembles a large piece of sheet metal with a flange on both the top and bottom). Install the hooked bracket hangers with the mounting plate attached on the mounting brackets installed on the television and measure the distance from the top of the wall plate to the top of the television.

5

Measure the distance from the side edge of the wall plate to the side edge of the television and write down these figures. These measurements will allow you to determine the correct mounting area for the television before you install the wall plate to the wall. The hooked bracket hangers are designed to slide from left to right on the flanged portion of the wall plate; make sure the wall plate is centered from right to left when you temporarily install it on the back of the television for accurate measurements.

6

Unhook the wall plate from the rear of the television and find your wall studs with a stud finder in the area where you wish to mount the television (the studs run vertically inside your wall). Mark the center of the studs with a pencil, using the wall plate as a template when marking the stud locations. There are multiple hole slots available on the upper and bottom portion of the wall plate that you can use.

7

Rest a level on top of the wall plate before using a drill to screw in the four bolts needed to secure the wall plate to the wall (two bolts top and bottom, on both right and left sides of the wall plate. The level will help you evenly mount the television to the wall). If your drill is not powerful enough to drive the bolts into the studs, drill pilot holes with a small drill bit and tighten the bolts using a ratchet tool.

8

Check the levelness of the wall plate again after you tighten down the bolts. Ask another person to help you lift the television and place it on the wall plate. The hooked brackets mounted on the television must slide over the upper flange of the wall plate so it can support the television. Certain mounts may have a flat rod that needs to be inserted in the bottom flange to secure the bottom potion of the television to the wall plate.

9

Hook up your audio, video and power cables to the television. If you are installing a wiring loom to hide your television cables, go ahead and install this now according to the product's instructions. Place the level on top of your television once more to check for levelness.

Some homeowners like to create an attractive focal point in their den or living room by mounting a flat-screen TV on a brick wall. The job requires different hardware with more specialized drill bits. But with the proper tools and planning, the results can be impressive.

Instructions

1

Place the bracket on the wall. Align at least 4 bolt holes on the brick (not the mortar) at the desired mounting height. Mark these locations with a pencil or the drill bit tip.

2

Drill the marked locations with the masonry bit. Make sure the bit penetrates at least 1/2-inch deeper than the maximum depth of the expanding anchors.

3

Insert the expanding sleeves into the drilled holes. Tap them in flush with the brick, using the hammer.

4

Place the wall bracket over the sleeves so the bolt holes are aligned with the sleeve openings. Insert the bolts and washers through the mount's holes and hand-tighten. Secure the rest of the way with the socket wrench and appropriate insert.

5

Give a quick tug on the bracket to ensure it is mounted securely.

Most flat screen TVs are VESA-compatible and designed to mount on a wall. "VESA" refers to standardized mounting holes on the back of plasma or LCD TVs. Although installation is fairly simple, getting power to the set can be a challenge. The easiest and neatest way to accomplish this is to have a licensed electrician install an outlet behind your proposed TV. Once an outlet is installed, thread your coaxial and speaker cables up to the TV between two studs behind the drywall.

Instructions

1

Slide an electronic stud finder across the wall to locate two suitable wall studs; the instrument will beep when it reaches the edge of a stud. Lightly mark the position of the middle of the studs on the wall with a pencil. Run the stud finder up the wall between the studs to ensure that there is no hidden fire block or obstruction preventing threading the coaxial cable up to the TV.

2

Lift the TV mounting bracket up to the desired height and location. Move the bracket until the two mounting holes line up with the center of the hidden studs. Place a spirit level horizontally on the bracket and center the bubble. Insert the tip of a pencil into each mounting hole and mark its outline with a circle.

3

Drill two lag bolt holes into the studs through the two circles with the recommended pilot drill bit and a cordless drill/driver. Position the bracket against the wall and insert the lag bolts that came with the kit into both pilot holes. Snug the bolts down with a socket wrench.

4

Level the bracket with the spirit level by tapping one side up or down until the bubble is centered. Tighten the lag bolts securely.

5

Drill a 1/2-inch hole through the drywall in the middle of the large opening on the mounting bracket. Drill a second 1/2-inch hole above the skirting board directly below the first hole. Insert a fish tape through the upper hole, thread it downward and fish the end out from the lower hole with a bent piece of thin wire.

6

Tape the end of the coaxial and speaker cables securely to the fish tape. Pull the fish tape up while feeding the cables through the hole from the bottom, and fish the ends out through the upper hole.

7

Lay your Polaroid Plasma TV face down on the carpet or on a thick towel. Pry the four plastic plugs out of the VESA mounting holes on the back of the TV with a thin screwdriver. Place the swivel or wall mount that came in the kit on the TV and line up the mounting holes. Attach the mount to the TV securely with the screws provided in the kit; use a Phillips screwdriver or nut driver, whichever is applicable.

8

Lift the TV into place with the help of a friend. Attach the security cable provided to the back of the swivel mount by following the instructions in the manual. Connect the coaxial and speaker cables to the TV.

9

Hook the upper lip on the swivel or TV mount bracket over the matching recess on top of the wall mounting bracket, and lower the TV into place.

10

Plug the power cord into the previously installed outlet behind the TV to complete the installation